SET YOUR VEHICLE
FREE SHIPPING ON ORDERS OVER $70!
Order Now, Pay Later
TALK TO A PARTS EXPERT
LOWEST PRICE
Guaranteed

Brian

Brian

Garage

Reviews

Brian has reviewed 9 Product(s).


    Stinger
    BJR 3 years ago
    I purchased this with the 1/4 pounder bumper and installed at the same time. Stinger comes with new hardware package that has longer caaphead bolts. Overall, the powder coating and welds are high quality, but the angles on the attachment points were off by approximately 10 degrees, which cause the top mountains no bolts to bow the top flange. After torquing all bolts it’s not really apparent but noticeable. The biggest issue now is getting to the engine! I have to crawl up through the stinger to work on the engine now. Never thought of that prior to the install!
    EVO Manufacturing Revolution Stinger Textured Black

    Nice bumper
    BJR 3 years ago
    I bought the bumper after seeing it on several other Jeeps. Quality and fit of the bumper are spot on! Very nice bumper! Highly recommend this bumper and the EVO Stinger!

    EVO Manufacturing 1/4lbs Front Bumper, Black

    Strength and Confidence
    BJR 4 years ago
    I upgraded the front axle housing on my 2012 JKUR just prior to my Moab trip with the unlimited 0.500in wall tubes. Also put in RCV shafts. The trip was 4000 miles round trip with 5 days of Moab trails to include, Poison Spider, Golden Spike, Gold Bar, Top of the World, Cliffhanger, Metal Masher, and a few more. This housing took some serious punishment and never flinched. Highway driveline vibrations are almost zero due to the additional pinion angle. No more worries about breaking or bending the front housing. The best part was I got to reuse my front e-locker and saved some money there. I couldn't be happier with the purchase. If you are on the fence about spending the money, just do it. It's the best money you can spend on the front end of your jeep IMO.
    Dynatrac ProRock Dana 44 Unlimited Housing Kit Front

    Awesome little compressor
    BJR 4 years ago
    I purchased this along with the EVO mount and installed under the hood of my 2012 JKUR and have been very impressed so far. The quality of all supplied components is impressive! Nice job ARB! As far as time of inflation, it takes a little over a minute to inflate each of my 37x12.50R17 Coopers from 15 psig to 28 psig. It’s fairly quiet as well and sounds very solid!

    ARB 12V Compact Air Compressor

    Installed in 2012 JKUR
    BJR 4 years ago
    I installed an ARB air compressor and needed this piece to mount the switch. It matches the black dash almost perfectly. Very easy installation and perfect fit and good quality. The only drawback is the interference with transfer case shifter. I have to flip my hand around to keep from smashing my fingers when going back into 4hi. This is the reason for less than a 5 star review. Wish they sold a three switch instead of the five.

    Rugged Ridge Lower Console Switch Panel

    Very nice!
    BJR 4 years ago
    I installed these on my 2012 JKUR front and rear with Lubelockers and couldn’t be happier. I really like the additional magnet and drain plug. The dipstick feather is really great along with the top fill. No more gear lube running down the front of the diff cover!

    ARB Dana 44 Differential Cover Black

    Great socks!!!
    BJR 4 years ago
    These are really nice socks and will be ordering again. Very comfortable!!!!
    Poison Spyder Crew Socks Black

    Worth every penny!!
    BJR 4 years ago
    Why did I wait so long? I’ll never mess with RTV again!!!!!
    Lube Locker Dana 44 Gasket

    Good mount but needs modification for 2012 JKUR
    BJR 4 years ago
    Mounted the single ARB compressor under the hood of my 2012 JKUR. The quality of the EVO mount is good with a nice finish, but I had to cut the back right corner off to eliminate interference with a bolt on the firewall. Also had to cut off the supplied bolts to eliminate the interference with the top of the master cylinder while keeping low enough to clear the hood. Then adjusted the bends on the arm to keep from using washers to shim under where it mounts to the existing fender bolt. Overall, not a bad mount for the money.

    EVO Manufacturing Air Compressor Mount Kit

Questions

Brian has asked 1 Question(s).

  • AnswerQ: MHT Fuel D694 Covert Wheels  BJR 4 years ago

    Are these wheels hub centric?


Answers

Images