-
Q: Install Azrel91 year ago
Hello, If I am adding this to my Dana 44 on a x model how does the wiring for the e locker leave the differential? Do you have to drill? Is there any supporting items I need to install this or any other parts I need to replace in my diff? Thank you.
-
-
0 of
0 people found the
following answer helpful
A: Yes, you will have to drill a hole for the wiring to come through. All parts needed are there.
Northridge Chris @ Northridge4x4 1 year agoWas this answer helpful?
-
0 of
0 people found the
following answer helpful
-
Q: Dana 44 Jeep JK Roger D2 years ago
-
-
0 of
0 people found the
following answer helpful
A: Yes, this will work with the 5.13 gears.
Northridge Chris @ Northridge4x4 2 years agoWas this answer helpful?
-
0 of
0 people found the
following answer helpful
-
Q: packaging keith53493 years ago
-
-
0 of
0 people found the
following answer helpful
A: They should come packaged with packing paper to fill the extra room in the box so the locker can't move all around.
Northridge Chris @ Northridge4x4 3 years agoWas this answer helpful?
-
0 of
0 people found the
following answer helpful
-
Q: JKU Sport Mcorona3 years ago
-
-
0 of
0 people found the
following answer helpful
A: This is the correct locker for you. Any brand (Yukon, Ten Factory, Revolution, etc) of the 5.13 gears will work with this locker. Here's an example of the part number for the gears; YUKYGD44JK-513RUB
Northridge Chris @ Northridge4x4 3 years agoWas this answer helpful?
-
0 of
0 people found the
following answer helpful
-
Q: Axle shafts Graham3 years ago
-
-
0 of
0 people found the
following answer helpful
A: You will have to upgrade the shafts too.
Northridge Chris @ Northridge4x4 3 years agoWas this answer helpful?
-
0 of
0 people found the
following answer helpful
-
Q: 3.73 and down jeepmountain4 years ago
-
-
1 of
1 people found the
following answer helpful
A: It technically means lower numerically(3.55, 3.21), but, the JK's use a thick cut gear set in the rear Dana 44 so all gear ratios use the 3.73 and down carrier(3.21 all the way through 5.38)
Northridge Kaleb @ Northridge4x4 4 years agoWas this answer helpful?
-
1 of
1 people found the
following answer helpful
-
Q: Fitment for gears higher than 3.73 Phillip4 years ago
-
-
1 of
1 people found the
following answer helpful
A: This is the correct locker for a JK Wrangler using 4.88 gears. The JK Dana 44's use a thick cut gear set so all ratio's would use the 3.73 and down carrier.(this is for the rear Dana 44, non-Rubicon)
Northridge Kaleb @ Northridge4x4 4 years agoWas this answer helpful?
-
1 of
1 people found the
following answer helpful
-
Q: Jk Rubicon eaton elocker. Brandon4 years ago
-
-
0 of
0 people found the
following answer helpful
A: This will not work in the Rubicon housing. The only elocker option for the Rubicon front axle is the Dana factory locker, found here. https://www.northridge4x4.com/part/lockers/2007503-dana-spicer-44-e-locker-front-differential-locker
Northridge Kaleb @ Northridge4x4 4 years agoWas this answer helpful? -
0 of
0 people found the
following answer helpful
A: ARB now makes a locker to fit Rubicon housings.
wvjeepguy81 @Was this answer helpful?
-
0 of
0 people found the
following answer helpful