SET YOUR VEHICLE
FREE SHIPPING ON ORDERS OVER $70!
TALK TO A PARTS EXPERT
SPECIALS!
Customer Photos and Videos
No user media. You can upload a photo or video of your install by posting a review.
5out of
5stars
sean
Northridge shipped super fast the week before Christmas. My son and I got these fully installed in about 90 minutes following the instructions from Oracle. A few YouTubers say to take the bumper off but that looked like more work than necessary. There is a tricky screw to remove and even more tricky to reinstall. The angled wrench shown in the instructions is a must and an electric angled wrench would be best. While holding the screw in place with a magnetic wand I was able to hand tighten the new fastener while my son held the plastic bumper molding away from my hand. These seem more pure white than the Oracle reverse lights I put on my Gladiator. The Gladiator lights have a yellowish tint to them while these match the JL's reverse tail light color better. I would buy these again and I would install them with the rear bumper on again.
5out of
5stars
JJsJL
Great product. I did install into my steel bumper and needless to say that was a pain on just one side. I watched the videos on filing down the housing to get them to fit. The one side that is filed down isn't seated exactly the same as the other but without really looking you can't tell. Lights do work great and really add additional lights we in reverse. I paired them with the harness Oracle offered to tie them in to the tail light for a plug and play install.
5out of
5stars
Mike
I read the previous review so I knew there was a chance I would have to do some filing to get the driver side installed and I was not disappointed. The left fits snugly with a little pressure applied it popped right in. The right was a no-go until I took a file to the bottom of the inside angled corner. It took a few passes but it wasn't too bad, most of the time was spent walking back and forth between the workbench and bumper. Once installed the wiring was also a bit of a challenge. I decided to wire directly into the trailer hitch reverse wire below the bumper and grounded directly to the frame. Simple and works great. The lights themselves are really bright and out of the way. I would recommend these to a friend.
4out of
5stars
SG68
I have a 2019 Jeep JLU with the standard halogen lights (non- LED). Install was pretty easy, but longer leads off the lights would be better. It would make attaching to the rear lights easier. Secondly, after I installed lights they would come on for a second and then go off after putting Jeep in reverse. Or they wouldn’t come on at all. I thought I had wires wrong, but I followed instructions exactly. I thought a loose or bad connections, but not the issue. I finally emailed Oracle and they told me the regular non-LED bulbs have a lot of resistance and added these lights caused them to flicker and go out or not come on. They suggested added LED bulbs in place of the halogen bulbs and it Would solve my issue. I bought the LEB bulbs and it certainly did solve the problem. They are bright and definitely help. Only thing I wish is they would mention that in there paperwork, instructions and website. Perhaps they will now. I took off a star because of the headache it caused trying to figure this out. Hopefully my review will helps others if they run into the exact situation I had.
1 of 1 people found the following review helpful
3out of
5stars
Butch
Very pricey and even harder to install. Others are making them at almost 1/2 the price.
4 of 4 people found the following review helpful
3out of
5stars
Mike
These lights are super bright and great add to any JL with the factory bumper. However, if you have the steel bumper, beware that Oracle still hasn't fixed an issue that has been reported by many people. The driver side area (Left) is just a bit smaller then the right hand side so there is no way to insert the new light fixture without cutting away at the aluminum housing. When I contacted Oracle support, they actually emailed a link to a 3rd party YouTube video showing this same issue. So be prepared to Dremel it to make it work. Also the instructions that come in the box are crap, they miss a few steps but their online video at least covers most of what you need to do. That being said, it is pretty easy install otherwise. If the light would have been designed to the correct size, it would have taken longer to remove the bumper then to install these things. If you have a plastic bumper, you shouldn't have an issue. They still give you crappy splice connectors, I would personally use some Posi-Taps instead, but since the install took so long with having to modify the house, I used the cheap connectors they provided in place for now.
3 of 3 people found the following review helpful
1out of
5stars
Jeepndogs
I loved the light output of the lights but unfortunately they don’t fit proper in the steel bumper. The solution from them is to grind light down to fit. This results in the seal in the lens being compromised and the light will eventually fill with water. Then you are expected to pay for shipping from them for the replacement that still doesn’t fit and you need to grind that one also, which will eventually leak. They insist it’s a Jeep problem with the steel bumper but Jeep only sells one factory reflector for the steel bumper and the plastic bumper……so you decide where the problem is. I would not recommend this product.
Product images
