-
Q: Big boy steering gearbox Church2410 months ago
I have a 2013 Jeep Wrangler Sahara with a stock steering system in it now if I just change the gearbox am I going to be able to use my stock pump and everything else
-
-
1 of
1 people found the
following answer helpful
A: Short answer is no, the stock pump will not push enough pressure to feed the new box.
Northridge Chris @ Northridge4x4 10 months agoWas this answer helpful?
-
1 of
1 people found the
following answer helpful
-
Q: Hydro-Assist Ryan2 years ago
-
-
0 of
0 people found the
following answer helpful
A: This one is not ported. You will want the PSCSG688R for the option to add ram assist later on. https://www.northridge4x4.com/part/hydraulic-steering-kits/sg688r-psc-big-bore-steering-gear
Northridge Chris @ Northridge4x4 2 years agoWas this answer helpful?
-
0 of
0 people found the
following answer helpful
-
Q: Will the XD2 work with Teraflex HD Trackbar without clearance issues? dmulk3 years ago
-
-
1 of
1 people found the
following answer helpful
A: The track bar shouldn't interfere with the steering box.
Northridge Chris @ Northridge4x4 3 years agoWas this answer helpful?
-
1 of
1 people found the
following answer helpful
-
Q: Are the XD2's "rebuildable" and work with Teraflex components? dmulk3 years ago
-
-
0 of
1 people found the
following answer helpful
A: Yes, this PSC box will work with Teraflex components.
Northridge Chris @ Northridge4x4 3 years agoWas this answer helpful?
-
0 of
1 people found the
following answer helpful
-
Q: Big Bore xd steering box 2014 JKU TomMartin3 years ago
-
-
0 of
0 people found the
following answer helpful
A: Yes it will work with Steer Smarts.
Northridge Chris @ Northridge4x4 3 years agoWas this answer helpful?
-
0 of
0 people found the
following answer helpful
-
Q: Torque specs Frank3 years ago
-
-
1 of
1 people found the
following answer helpful
A: 87 foot pounds for the steering box bolts into the frame, and 185 foot pounds for the steering sector nut.
Northridge Chris @ Northridge4x4 3 years agoWas this answer helpful? -
1 of
1 people found the
following answer helpful
A: I finally got a hold of PSC and was told these were the torque specs "220-240 on the pitman arm and factory specs on the 4 mounting bolts which should be 87 ft pounds."
Frank @Was this answer helpful?
-
1 of
1 people found the
following answer helpful
-
Q: drop pitman arm toad3 years ago
-
-
0 of
0 people found the
following answer helpful
A: You would need to go to a drag link flip and raised track bar bracket(if you don't have one). The pitman arm with this box isn't a drop and your drop won't work with it.
Northridge Kaleb @ Northridge4x4 3 years agoWas this answer helpful?
-
0 of
0 people found the
following answer helpful
-
Q: Pittman Arm Pat 3 years ago
-
-
0 of
0 people found the
following answer helpful
A: The supplied Pitman arm does not have any additional drop to it, therefore some applications may require a drag link flip kit.
Northridge Chris @ Northridge4x4 3 years agoWas this answer helpful?
-
0 of
0 people found the
following answer helpful
-
Q: Pump Variations XD vs XD2 feroxjb3 years ago
-
-
1 of
1 people found the
following answer helpful
A: The XD2 is the second version of the Big Bore XD gearbox. You may see it listed both ways but all the Big Bore gear boxes we have(ported or non-ported) are XD2.
Northridge Kaleb @ Northridge4x4 3 years agoWas this answer helpful?
-
1 of
1 people found the
following answer helpful
-
Q: Will this work with Synergy Sector Shaft Brace? Mibbj 3 years ago
-
-
0 of
0 people found the
following answer helpful
A: The sector shaft brace will not fit with the big bore box, but isn't necessary.
Northridge Chris @ Northridge4x4 3 years agoWas this answer helpful?
-
0 of
0 people found the
following answer helpful
-
Q: Used with oem steering pump Frank4 years ago
-
-
1 of
1 people found the
following answer helpful
A: It can be used with the OEM pump, but PSC highly recommends the use of their HIGH FLOW/HIGH-PRESSURE Pump Kits to ensure system efficiency and extend component life. These pumps operate at approximately 1800 PSI and produce 50% more volume than the OEM pump. Vehicle steering performance will be diminished if a high mileage or remanufactured component is used. I would recommend to do the Overlander kit from PSC. It will be a much larger improvement over just the box. https://www.northridge4x4.com/part/hydraulic-steering-kits/sk284-psc-big-bore-xd-overlander-steering-kit
Northridge Kaleb @ Northridge4x4 4 years agoWas this answer helpful?
-
1 of
1 people found the
following answer helpful
-
Q: PSC big bore steering box Brennon Burkhart 4 years ago
-
-
2 of
2 people found the
following answer helpful
A: No it does not. You would want the SG688R
Northridge Kaleb @ Northridge4x4 4 years agoWas this answer helpful?
-
2 of
2 people found the
following answer helpful
-
Q: Big Bore XD steering box Pmills5 years ago
-
-
2 of
2 people found the
following answer helpful
A: There is not a different pitman arm available for this steering box. There are a few factors that could play in to the floaty feeling that you have. It would be best to give us a call @ 866-601-5340 to discuss what may be going on.
Northridge Kaleb @ Northridge4x4 4 years agoWas this answer helpful? -
1 of
1 people found the
following answer helpful
A: Did you ever find out? I’m considering getting this for mine? I’m running 2.5 lift on 35s. Thanks!
MLott91 @Was this answer helpful?
-
2 of
2 people found the
following answer helpful