Fox 2.0 Performance Series TS Steering Stabilizer - 1 5/8in Tie Rod
JK
Product Resources
Features & Product Details
With conventional steering stabilizers, turning in one direction creates an increase in pressure inside the stabilizer as the shaft occupies more volume in the body and displaces the oil. The repercussion is a push or pull steering force felt by the driver as the stabilizer attempts to return to its neutral state. To overcome this unidirectional force, dual opposing stabilizers are often used, but this requires additional mounting hardware and space.
Derived from the FOX's original ATS stabilizer, the Performance Series 2.0 Stabilizer TS utilizes a Through Shaft (TS) architecture that eliminates shaft fluid displacement throughout the stabilizer's entire travel in both directions. By eliminating fluid displacement, the TS design delivers neutral and consistent damping of unwanted steering feedback. The result is unrivaled steering control at an unbelievable price point in a single, bolt-on stabilizer.
The Performance Series 2.0 Stabilizer TS includes application specific mounting hardware and is available in multiple clamp sizes for stock or aftermarket heavy duty tie-rods.
Shock Body Diameter: 2”
Shock Body Material: 6061-T6 Aluminum
Shock Body Finish: Clear Hard Anodized
Shock Component Material: 6061-T6 Aluminum
Shock Component Finish: Black Hard Anodized
Shaft Material: Heat-Treated Steel Alloy
Shaft Finish: Hard Chrome Plating
Piston: Race-Developed High-Flow Design
Redundant Valve Seals: Main Seal, Wiper Seal, and Scraper Seal
Shock Oil: JM92 Advanced Suspension Fluid
Shock Gas: High-Pressure Nitrogen
Bushing Material: Black Nitrile Rubber
Charge: Neutrally Charged
Extended Length: 23.27” (591.06mm)
Collapsed Length: 15.08” (383.03mm)
Travel: 8.19” (208.03mm)
Specifications
PEOPLE WHO VIEWED THIS ITEM ALSO VIEWED
QUESTIONS & ANSWERS
-
Q: 1.5 Shawn 3 years ago
Can this work for a 1.5 tie rod
-
-
0 of
0 people found the
following answer helpful
A: This will only work on an 1 5/8" tie rod.
Northridge Chris @ Northridge4x4 3 years agoWas this answer helpful?
-
0 of
0 people found the
following answer helpful
-
Q: JLU?? Scott4 years ago
-
-
1 of
1 people found the
following answer helpful
A: Yes, this will work on the Steer Smarts extreme tie rod that is 1 5/8 in diameter.
Northridge Chris @ Northridge4x4 4 years agoWas this answer helpful?
-
1 of
1 people found the
following answer helpful
-
Q: Custom tie rod eserf4 years ago
-
-
0 of
0 people found the
following answer helpful
A: Yes, the clamp can be removed, but it is not recommended.
Northridge Chris @ Northridge4x4 4 years agoWas this answer helpful?
-
0 of
0 people found the
following answer helpful
-
Q: FOX 2.0 steering stabilizer 1 5/8" tie rod steve4 years ago
-
-
1 of
1 people found the
following answer helpful
A: This is for a 1 5/8" tie rod, like the SteerSmarts. If you have a stock tie rod(or Synergy), then you would need the one with the 1 3/8" clamp, which can be found here.: https://www.northridge4x4.com/part/shocks/985-02-121-fox-2-0-ts-steering-stabilizer-stock-1-3-8-tie-rod-clamp
Northridge Kaleb @ Northridge4x4 4 years agoWas this answer helpful?
-
1 of
1 people found the
following answer helpful